subwoofer settings car

Will I alleviate my fear of burning out or slapping my Blaupunkt sub by switching it out to a sub with higher power handling? Click on. anyone tell me how to install in car CHEVY impala.nd which gauge wires i need.??????? It says to set the LC7i's gains with the amp's gain turned all the way down at first. The welds in some such vehicles involved in crashes were found to have spilt along hairline cracks, introduced by the use of subwoofers, or by panels splitting at rust points. Do not lower the gain of your full-range amplifier to try and match your lack of subwoofer volume. I saved for months and bought an Alpine MRX-M55 amplifier and a Rockford Fosgate P2-1X12 loaded enclosure and had them installed at Best Buy. Keep up the good work!! Buck, I went ahead and bought the Oscilloscope ARM DSO Nano DSO201 so I can really tell if I am clipping. But that didn't help either. You want the fuse as close to the battery as possible. Crutchfield collects state sales tax on items shipping to the following states: AK, AL, AR, AZ, CA, CO, CT, DC, GA, HI, IA, ID, IL, IN, KS, KY, LA, MA, MD, ME, MI, MN, MS, NC, ND, NE, NJ, NM, NV, NY, OH, OK, PA, RI, SC, SD, TN, TX, UT, VA, VT, WA, WI, WV, WY. Dean, I suggest you set the subsonic filter to 36 Hz or lower and the low-pass filter to around 90 Hz. 2 MTX 10" powered by 1200 watt pioneer mono amp. OK now we have most of the wires in place, we can wire up the amp.Connect the power cable from the battery into the spot on the amp that has one of the following markings (do not connect it to the speaker positive): B+ Batt. Hello, My question is: Be careful. Please help me, I don't know what these things mean and where to set it. Kicker Solo Baric S1217 Sub (trunk) BTW, I did not rely on your method for this; I just used my ears to set all of the controls on the amp. I have CF-purchased xav-ax7000 head unit w Pioneer TS-A1697C components in the front and TS-A1670F 3 way coax in the rear doors of my 2011 Honda Element. Seemingly complex at first, now I can refine the system at will. Go ahead and fiddle around with things, have fun. Thank you. This article, and your other on 4 channel full range amplifiers, just kicked my 2013 RAM 1500's system up several notches of awesome! As long as the signals are undistorted, those subs should handle that amplifier's output power just fine. Its ratings are:-400w RMS-1200w Peak-4 Ohm ImpedanceA good amp for this speaker (assuming this is the only speaker attached to the amp) might be the Rockford P400-2. 3 years ago, i think soldering it back and wrapping a ton of electrical tape should do it, 6 years ago For ported subwoofers, use a subsonic filter on your amplifier to tame any overly loud low notes. I ordered a new set-up through you guys and will be installing it myself, so I wanted to make sure I understand this right. Turn the gain up until it distorts, then back it off until the sound is clean again. Adjust the bass boost and subsonic filter, Step 5. Bradley, A general rule of thumb about electronic equipment is that if some part of a device's circuitry fails, it will be unwise or unsafe to continue using the device until it's been repaired or replaced. Randy, I read so many positive reviews on the Polk DB6501 components and how if you put power to them they will really crank out the sound but I have them on a Rockford Fosgate P300x2 and I am not sharing that experience. Filter out the cymbals, strings, vocals, and guitars. Why not just use an oscilloscope to set the max volume without clipping on the receiver speaker outputs, then you'll never feed your amp a clipped signal, repeat with the amp, and Done. Kicker 6x9 3ways (rear) If you want to use the low-pass filter of your amp to tune the bass, switch the crossover to "LPF" and turn off the low-pass filter of the receiver. There, it describes how to turn the full-range sound up and then raise the bass to match. Setting up the ideal sound system in your automobile starts with understanding the architecture and signal flow of a car audio system. Some subs have wide freq response for eg 20hz-1000hz and some subs have narrow freq response for eg. I think ill have it figured out i just dont know if they realy have 750 watt rms. Ive eliminated the high pitch noise coming through my speakers on start up, now trying to lower the 59hrz to a more suitable place without having to pay someone to build me a box. J, Following all the steps in this article should lead you to a balanced sound. In the manual, do i set it up how it is in example 3? I recently upgraded to the alpine ilx- 107. I'm assuming if I LPF is set to 80 on the HU, then the frequency control knob on the sub should be set at 80 also? I'm ordering today! Here is why. 4. on Step 1, the red thick cable where does it connect, I am trying to upgrade my subwoofers. I usually have the base on receiver all the way down mid at +3 and treb at +6. Zack, I'm not familiar with that amplifier, but you should be alright switching each sub to its 2-ohm setting and wiring the subs to the amp like this. The low-pass filter for the subwoofer channels should be engaged to keep high notes away from the sub's signal. Should it be turned all the way down? I was told it was a good match for my subs, 10" pioneer TSSW2502S4. Amp is a hitron hra 2500b. If the crossover slopes can be adjusted, set both the low- and high-pass slopes to the same setting… Thanks. It includes a pair of studio-quality headphones, a combination DAC (digital-to-analog converter) and headphone amp, USB mobile adapters, and a guide to getting the most out of your session. Crutchfield is servicemark of Crutchfield Corporation. Well I have a situation here which I bought an sound stream amplifier 4000 watts 1 ohm stable.then I want to use its max power rating which is 2000 RMS x 1@1 ohm. Using either a high- or low-level input for the sub amp has no effect on how much power the amp draws from the electrical system. This is the single most important factor when getting ready to setup your subwoofer. Buck Pomerantz. Or is the box just unable to play that particular range? Use one or the other, but not both. What about if i have an active sub woofer? But I can't tell for sure without knowing exactly what the amp is (brand name and model number). Jay, Amplifier gain should be set so no distortion can ever play, not for a specific knob position. I am getting some rattle and I'm positive that it is not blown. Remote Ant.Connect the 3 foot, 10 gauge wire to the one marked (do not connect it to the speaker negative): B- Neg -12v Gnd GroundConnect the other end of the ground wire to a nearby bolt that connects to the body of the car. This is the frequency at which your subwoofer starts playing bass notes. Their toll-free number is on your invoice. Thanks. It can be purchased separately? While listening to the music coming out of your sub, slowly adjust the sub amp's low-pass filter downward until all the high- and mid-frequency notes disappear. can using a high/low converter effect tuning an amplifer? Click on this link for details. It seems like your method will keep the power below the max threshold by avoiding distortion. It would be greatly appreciated.