Nice idea, BUT, just like so many of the instructables, the only location for the parts list is in the little picture boxes and when I download the instructable as a pdf on my Mac no list is visible :-/ Any list available? We’ll help you to make your home give you and your family as much beauty, happiness and joy as possible. The threaded end will screw into the base of the tee, and the slip end will fit over the end of the shorter PVC pipe (for extra power, you can glue the adapter to the pipe) See the pictures for a more complete explanation of how this works. This is true. Reply In this DIY guide, Matt Haas was able to craft a microphone stand using scrap wood. If the answer to that question is yes, then you probably made a huge mistake. You too can make this for yourself, it might take a while, but you’ll definitely get it done. You would need to have some woodworking experience to make this. The total cost of making this is quite affordable for most persons. I'm positive that you can buy actual mic clips, but whilst I was at the Home Depot, I found a PVC fitting called a 'slip-snap' fitting. The process of making this isn’t as easy as it seems, but I’m sure you’ll get the hang of it. Have you ever had pringles and thrown the case away afterward? If you have ever purchased a mic stand before or compared the prices online, you would agree with me that mic stands are quite expensive online. In addition, I would suggest a grease on the threads although for obvious reasons the grease cannot contaminate the the clamping area. 4. The creator of this project was able to craft an amazing mini mic stand. First up… The 6 Categories of Mic Stands. @trustsound The boom arm would perhaps be the trickiest part of this DIY. So remove the ring at one end, loosen up the other end, and slip your PVC segments into each tee. This is yet another amazing mic stand hack. ... perhaps a thin sheet of plastic on it's inside to allow slide?- Randy, Question Here’s the step-by-step guide on how to build a DIY mic stand for your amp. Hardware stores don't carry these kinds of joints (to my knowledge) - so we'll be using the union tee fittings to achieve a similar effect. 3. If you are a handyman, replicating this shouldn’t be a hard task. There's a lot of room for tweaks and adjustments here, but it does what it's supposed to do! Very nice! I might have to just think about simple straight (non boom) DIY stands… Question The pipe screws into the plate on the board, and the boom arm assembly screws onto the top of the pipe. That part was the first part of the ones I purchased from Radio Shack to give out. I want to buy this 10-pack.. NOW! I was in awe at first sight. $10 a stand (including booms)!!!! In this DIY guide, the creator was able to craft a great looking pringles mic stand. and when I look online for 1/2 threaded union Tee I cannot find that exact part. NEXT (ready?) In this DIY project, the creator was able to make a boom arm using cardboard and a couple of other materials, the making process is quite easy and fun to follow. It cost $10 to put this together. Well, have you tried PVC? Grab the bottom of the hanger with the pliers, and pull. Definitely leaving both washers in will make it more secure - I just thought it might be a bother to have to loosen both ends of the tee to make adjustments. In this DIY guide, you’ll learn how to make a cheap mic stand. There are a lot of DIY mic stand projects that show how to make a PVC mic stand, but most PVC mic stands can’t be adjusted. It is ideal for the little ones. Take your mic to the hardware store to measure the clips- make sure it fits. And we're going to connect the longer 2' tee to the shorter one, using the 1/2 inch threaded adapter. Halloween Pumpkin With a Moving Animatronic Eye | This Pumpkin Can Roll Its Eye. In this article, I have listed a lot of mic stand projects that would inspire you to make your very own mic stand. I was in awe while watching the making process of this DIY Boom pole. I have seen a lot of musicians struggle with mic stands for their amps. Well, you don’t need to spend a lot of money for a new mic stand. Have fun! On either end, there's a sort of cap that screws on and off, and inside that cap is a little rubber ring. With over thirty years as part of the DIY and Punk scene, Thomas Lopez embodies the spirit of innovation and … The creator will show you how to convert a camera tripod into an amazing mic stand. Reply Make sure all your fittings are the right diameter! If you are a handyman, making this should not be a hard task for you. May I make a suggestion? since the tee joint on my boom arm was threaded, I went ahead and got a 1/2 inch metal threaded pipe. SUBSCRIBE FOR OUR NEW VIDEOS This is a video about How to make a Microphone stand at home just using a PVC Pipe. 2 years ago After trying to explain pivot joints to about three different hardware store employees, I stumbled on this - it was as close as I could get, but it works very well. Stretch out the hanger. All the components for this mic stand can be found at the hardware store. In this DIY guide, the creator was able to make a mic stand in 5 minutes. It is beautiful, easy-to-make, and inexpensive. on Step 5. this baby works like a charm for mics - if you can't find one, try a simple 1/2 inch tee fitting - the mic won't 'snap' in, but it should slide in all the same. The collective wisdom of the internet will simply tell you to duct tape your mic to a broom and lean it up against a chair. He made this mic stand using scrap materials in his shop. Next time, don’t throw it away. If any of your fittings are larger than 1/2 inch, make sure your pipes and connectors are also larger - everything has to be the right diameter to fit together! I would suggest a piece of rubber hose of the appropriate diameter be applied over the nuts and held with glue if necessary. on Step 1. where did you get the "1/2 threaded union Tee?" I think this is a great project, you can make it from the comfort of your home with a few supplies handy. Using PVC and a couple of rubber bands, the creator was able to piece together this unique DIY Mic stand.